No sintoniza ningún canal:
[code]vdr:~$ dvbscan -a1 -o vdr dvb-t/es-Madrid | tee canalesT.conf
scanning /etc/dvbscan/dvb-t/es-Madrid
using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'
initial transponder 770000000 0 2 1 3 1 3 0
initial transponder 810000000 0 2 1 3 1 3 0
initial transponder 834000000 0 2 1 3 1 3 0
>>> tune to: 770000:I999B8C23D12M64T8G4Y0:T:27500:
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010
>>> tune to: 810000:I999B8C23D12M64T8G4Y0:T:27500:
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010
>>> tune to: 834000:I999B8C23D12M64T8G4Y0:T:27500:
WARNING: >>> tuning failed!!!
>>> tune to: 834000:I999B8C23D12M64T8G4Y0:T:27500: (tuning failed)
WARNING: filter timeout pid 0x0011
WARNING: filter timeout pid 0x0000
WARNING: filter timeout pid 0x0010
dumping lists (0 services)
Done..[/code]
aunque el nivel de señal es aceptable:
[code]vdr:# ./tzap -a 1 -c channels-conf/dvb-t/es-Madrid "TELECINCO"
using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'
reading channels from file 'channels-conf/dvb-t/es-Madrid'
tuning to 770000000 Hz
video pid 0x0191, audio pid 0x0193
status 1f | signal 913f | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal 913f | snr 8f8f | ber 00000000 | unc 00002b00 | FE_HAS_LOCK
status 1f | signal 913f | snr 8d8d | ber 00000000 | unc 00003300 | FE_HAS_LOCK
status 1f | signal 913f | snr 8e8e | ber 00000000 | unc 00003300 | FE_HAS_LOCK
status 1f | signal 913f | snr 8f8f | ber 00000000 | unc 00003300 | FE_HAS_LOCK
status 1f | signal 913f | snr 8e8e | ber 00000000 | unc 00003300 | FE_HAS_LOCK
status 1f | signal 913f | snr 8f8f | ber 00000000 | unc 00003300 | FE_HAS_LOCK
status 1f | signal 913f | snr 8f8f | ber 000037d0 | unc 00003300 | FE_HAS_LOCK
status 1f | signal 913f | snr 8e8e | ber 000037d0 | unc 00003200 | FE_HAS_LOCK
status 1f | signal 913f | snr 8f8f | ber 000037d0 | unc 00003300 | FE_HAS_LOCK
status 1f | signal 913f | snr 8d8d | ber 000037d0 | unc 00003300 | FE_HAS_LOCK
status 1f | signal 913f | snr 8f8f | ber 000037d0 | unc 00003200 | FE_HAS_LOCK
status 1f | signal 913f | snr 8f8f | ber 000037d0 | unc 00003200 | FE_HAS_LOCK
status 1f | signal 913f | snr 9090 | ber 00007fea | unc 00003300 | FE_HAS_LOCK

status 1f | signal 913f | snr 8f8f | ber 00007fea | unc 00003200 | FE_HAS_LOCK
status 1f | signal 913f | snr 8c8c | ber 00007fea | unc 00003200 | FE_HAS_LOCK
status 1f | signal 913f | snr 8e8e | ber 00007fea | unc 00003300 | FE_HAS_LOCK
status 1f | signal 913f | snr 8f8f | ber 00007fea | unc 00003300 | FE_HAS_LOCK
status 1f | signal 913f | snr 9292 | ber 000081b5 | unc 00003300 | FE_HAS_LOCK

The status messages have the following meaning:
status 0x1f --- The demodulator status bits.
0x1f means all bits set, everything ok.
signal [0x0000...0xffff] --- Signal Strength. Values above 0x8000 should be ok.
snr [0x0000...0xffff] --- Signal/Noise Ratio. Values above 0x8000 are ok.
ber [0...0xffffffff] --- Bit Error Rate. The less the better.
unc [0...0xffffffff] --- Number of Uncorrectable Blocks.
Small numbers are Preferable.
If everything is alright and all frontend circuits are working stable
(are locked) you should see a FE_HAS_LOCK in the rightmost line.
Good luck,
Holger[/code]

¿Qué pasa? ¿Porqué no pillo?
Gracias.

__________________
Goommer